binding

Is it ok to add an additional washer on top of your binding ... by Guest
Is it ok to add an additional washer on top of your binding fixing washer? My binding moves very slightly even tho both screws on binding tightened rt down.
The holes for the binding on my atomic hachet are not in the... by Guest
The holes for the binding on my atomic hachet are not in the center of the board, but a bit closer to the back - is this right? should the rear binding be closer to the edge of the board than the from...
Binding Angles by morelli
What binding angles should i use for freeride?
Best binding for park on K2 darkstar by Joshua
Hi what do you think the best binding are? currently looking at getting GNU pickel or the lib teck skate banana. Whats your preference?
cost of binding by guest
how much would normal a snowboard binding be.
What is the leash on the right binding for? by Guest
What is the leash on the right binding for?
I have switch N binding and i'm looking to get new boots as ... by Guest
I have switch N binding and i'm looking to get new boots as my old ones dont fit. I was wondering if that was even possible anymore. I need Size 10!
can aburton p1.1 binding work on a kemper board by Guest
can aburton p1.1 binding work on a kemper board
my daughter k2 binding are hard for her to rlease. is there ... by Guest
my daughter k2 binding are hard for her to rlease. is there anything i can do to make them release easier?
Advice on fixing a binding by onedub
I have a Burton Custom binding that cracked apart on the think plastic base that wraps around the back of your foot, just above the back of the heel. It`s pretty thick plastic, so I think it will g...
Riding using one binding by PerryRObray
What is it called when a person is only strapped into one binding when riding (not just lift lines, ect..) ? Are there different names for jumps, ect... when not strapped into both bindings ?
Can I drill new holes on my snowboard so my binding holes li... by Guest
Can I drill new holes on my snowboard so my binding holes line up? Will this ruin the board?
What board/binding size should i get and should it be a wide board? by ghost_1260
i'm 135lbs and 5ft. 6in. i have 10.5 boots. my binding stance is 9, 9. i currently ride a 151 burton blunt but i wanna get a smaller board for jibs and jumps. i need new bindings as well. what si...
What size binding do you get for a certain boot size? by Guest
What size binding do you get for a certain boot size?
bindings by seanl1
can any one help after last qeestion decided to take my k2 binding s back and now need to decide whitch burton binding to buy .i need a comfortable allround binding have already had missions
Switching from soft to hard boots? by RyougaZell
experience of this? I`d say that there`s no real point in using a good hard boot with a sloppy binding. Sure, there are some reasonably good traditional hard binding systems out there, but my ow...
Flow Bindings in Canada? by narilia
Anyone know where to get Flow Bindings in Canada? The seem pretty rare. I have seen a lot of posts about best boots to go with those bindings. I would not mind some opinons. Are they w...
Tips 'N' Tricks by PerryRObray
Practicing very slow speed maneuvers without bolting in the back binding can enhance/sharpen skating skills needed for getting on and off chairs. Some resorts have cat trails which may be traversed fa...
SI bindings by weaponxx1
...t doesn`t fit, the whole system is compromised. So, don`t make the same mistake I did. Before you get the bindings, make sure the boots will fit. The interface between the boots and the bindings ...
Can I combine butron freestyle bindings with Freeride or Freestyle? by PerryRObray
If your toes are overhanging 1 inch and no overhang on the heel, it may be possible to move the binding to reduce toe overhang. Pretty much any binding will go on any board nowadays(since the 4x4 ...
Help with K2 Clickers by Brandon77
I have used k2 clickers in the past, in Maine, and they are a pain. Since the binding is almost flat its nearly impossible to keep snow/ice from the binding and the bottom of the boot. I use the Vans ...
Burton SI boots and bindings FS by JaiGuruDevaOm
Why do you want to sell them ? I just tried out the same setup (SI binding 99 the one with the hologram on the HB, Ruler SI 99 Size 9.5). The binding performed fantastic, the boots caused some pain (u...
What board to buy? by kopplj92
You definitely can use Burton binding with other boards. Most Burton binding come with both the 3 hole and 4x4 base plates, or a combo base plate. Burton is the only manufacturer that I know of that...
What are good binding positions? by Old Zircon
I am new to snowboarding and I was wondering what is a good positioning for my bindings? Is there a safe place to start? I know shoulder length apart, but what about the degree settings?
Stomp Pads by adam8642
...i there, i have always used stomp pads. i am using a demon tool stomp pad at the minute. it has a built in binding tool and spare binding screws and washers. i like it because it has little plastic...
Does it matter if i buy freestyle bindings,but have a freeri... by PerryRObray
In the past the more freestyle orientated a binding was, the more ankle movement will most likely happen. The bindings with more support (non freestyle) will help on turning and compromising situation...
Quickest Strap Binding (ENTRY/EXIT) ? by Stokes
...tory... So, what is the easiest set of straps to attach/remove? So far I like the look of Ride SPi bindings, but haven`t demo`d them. Thanks! -t...
Step-in vs. Straps - my experience by jordan_16
I prefer strap-in bindings because I rode in step-ins one season and my foot came out of the binding. My binding was always cloged with snow, which made it difficult to step-in. My brother has step-in...
  More Topics...

The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 Snowboard Gang